新葡的京集团8814-首页

产品选型
Product model
Current location:

How to Send Specifications for a Temperature Sensor RFQ: Required Parameters, Writing Examples, and a Ready-to-Use Template

Number of Views:2962026-11-16 11:41:42

In one sentence: A temperature sensor RFQ should be sent in four layers — application conditions, electrical specifications, mechanical/interface details, and commercial terms. The mandatory fields are: measured medium and mounting location, operating temperature range, nominal resistance at 25°C and B value (with the reference temperature pair stated), resistance and B-value tolerances, the resulting accuracy in ±°C over a defined band, probe dimensions and housing material, cable insulation type and length, connector part number, ingress protection rating, annual volume, and sampling requirements. An RFQ that says only "one temperature sensor, −40 to 125°C" will not produce comparable quotes.


1. Why an incomplete RFQ makes quotes incomparable

The phrase "10K NTC temperature sensor" can describe a dozen different products in a supplier's catalogue: epoxy bead or glass-sealed body, PVC or PTFE cable, ±1% or ±5% tolerance, calibrated per band or shipped as a standard bin, with or without a connector. These differences routinely produce unit prices that differ by two to three times — while the buyer is comparing what looks like the same line item.

Three things follow from an incomplete specification:

  1. Quotes cannot be compared. Three suppliers all quote "10K 3950," but tolerance, cable construction, and calibration method differ. The comparison becomes about price rather than about the same part.
  2. Sampling loops. The sample does not fit the mounting hole, the cable is too short, the insulation fails at temperature — each revision costs one to two weeks.
  3. Drift in mass production. Pilot runs pass, then production batches scatter and the whole control curve shifts. Rework costs far more than the unit price difference ever saved.

Sending parameters properly is therefore not a formatting exercise. It is the work of translating operating conditions into testable specifications.


2. A four-layer framework: who answers which question

Before writing the RFQ, split the requirement into four layers. Done this way, few items get missed.

Layer Question it answers Key parameters Typically owned by
Application What is measured, where, for how long Medium, mounting location, environment (humidity, vibration, corrosion), expected service life Mechanical / process engineering
Electrical What signal, how accurate Sensor type (NTC / Pt100 / thermocouple), R25, B value, tolerance, operating range, accuracy, response time Hardware engineering
Mechanical How it mounts and connects Probe diameter/length/material, thread or clamp, cable material and temperature rating, cable length, connector, IP rating Mechanical + production line
Commercial How many, by when Annual volume, batch rhythm, sample quantity, target price, certifications, packaging, delivery point Purchasing

Suggested sign-off order: application and electrical layers approved by R&D, mechanical layer confirmed by the production line, commercial layer filled in by purchasing. Send only after all four are complete — this gives the highest chance of a first-round match.


3. Electrical parameters: NTC is where most errors happen

3.1 R25 and B value — always state the reference pair

The two defining parameters of an NTC are the nominal resistance at 25°C (R25) and the B value (material constant). Common R25 bins are 5K, 10K, 50K and 100K; common B values are 3435K, 3950K and 4100K.

The most commonly omitted detail: the B value must state its reference temperature pair — B25/50 or B25/85. For the same die these numbers are not equal; B25/85 is typically higher than B25/50. Write only "B = 3950" and a supplier may quote against 25/50 while your R/T table was built on 25/85, shifting the entire temperature curve systematically.

Correct form:

R25 = 10 kΩ ±1%, B25/50 = 3950 K ±1%

3.2 Convert tolerance into temperature error before confirming

A ±1% resistance tolerance sounds precise, but it does not mean ±1°C. Near 25°C a 10K/3950 NTC changes roughly 4.4% per °C, so ±1% resistance corresponds to about ±0.2°C. Toward the ends of the range the same resistance tolerance maps to a larger temperature error.

State both levels in the RFQ:

  • Component level: R25 tolerance ±1%, B-value tolerance ±1%
  • System level: measurement error ≤ ±0.5°C over 0–100°C

The second sentence tells the supplier whether you need band calibration or standard binning — two options with very different cost and lead time.

3.3 Keep three "temperature ranges" separate

Many RFQs state a single "operating temperature −40 to 125°C." In practice there are three distinct concepts:

Concept Meaning Example wording
Operating range Range of continuous normal operation −40°C to +125°C
Accuracy band Range over which the stated accuracy is guaranteed ±0.5°C within 0°C to +100°C
Survival limit Short-term limit without damage 150°C for 30 min

Written separately, the supplier can judge which encapsulation, which cable, and whether special calibration is needed. Written as one number, it is usually quoted against the loosest interpretation — and the shortfall only appears on the equipment.

3.4 Response time and self-heating: two hidden accuracy killers

  • Thermal time constant (τ): typically several seconds to tens of seconds in still air; 1–3 s in water. If you are measuring a fast-changing temperature (outlet water, battery surface), τ must be specified, or you will receive a probe that is accurate but slow.
  • Self-heating: an NTC is read by passing current through it; excessive measurement current heats the element and biases the reading upward. Confirm the maximum measurement current or power so that self-heating error stays below roughly one-fifth of the accuracy requirement.

4. Pt100 / Pt1000 and thermocouples need a different form

NTCs are inexpensive and sensitive, but accuracy and consistency depend on binning and calibration. Pt100 sensors are stable and traceable but costlier and need excitation circuitry. Thermocouples cover wide ranges but are limited by accuracy and cold-junction compensation. The same RFQ table does not fit all three.

Pt100 / Pt1000 — required fields:

  • Tolerance class: AA (1/3B), A, B, C. Per IEC 60751, Class A is approximately ±(0.15 + 0.002|t|)°C and Class B approximately ±(0.30 + 0.005|t|)°C.
  • Wiring configuration: two-wire (lead resistance cannot be compensated), three-wire (industrial standard), four-wire (high-accuracy measurement).
  • Insertion depth and sheath material: insufficient immersion produces a significant conduction error.
  • Integrated transmitter: for 4–20 mA or RS485 output, state supply voltage and range.

Thermocouple — required fields:

  • Calibration type: K, J, T, E, N, etc. — range and sensitivity differ.
  • Wire diameter and sheath material: affects response speed and corrosion resistance.
  • Cold-junction compensation method: instrument-side compensation or extension wire run to an isothermal terminal.
  • Extension wire type: must match the calibration; a mismatch introduces errors of tens of degrees.---

5. Mechanical, interface and mounting: whether the sample actually fits

Item What to provide Common pitfall
Probe Form (bead / glass-sealed / stainless sheath / threaded), diameter, length "Make it small" — it will not fit the mounting hole
Housing material 304/316L stainless, brass, aluminium, engineering plastic, PTFE Standard stainless in a corrosive medium perforates within months
Cable Material (PVC / XLPE / PTFE / silicone), temperature rating, gauge, conductor count Length given without material — the jacket fails first in hot environments
Cable length Actual length from probe to connector, including tolerance No tolerance, so assemblies vary at installation
Connector Part number (e.g. XH-2P, PH-2P, specific Molex PN) and pin assignment "With terminals" — reversed pin order causes a batch-wide rework
Sealing and IP IP65 / IP67 / IP68, potted or not, oil resistance "Waterproof" that is actually only splash-resistant
Mechanical Pull force, bend cycles, installation torque Frequently omitted in automotive and energy-storage projects

6. Six items most often left out

  1. Medium corrosivity — coolant, electrolyte, oil mist, cleaning agents and disinfectants all constrain encapsulation material.
  2. Representativeness of the mounting point — core fluid temperature versus pipe-wall temperature can differ by several degrees.
  3. Insulation and dielectric strength — high-voltage platforms (e.g. 800 V systems) often require ≥100 MΩ at DC 500 V and AC withstand above 1500 V.
  4. Certification and compliance — CQC/UL for appliances, AEC-Q200 and IATF 16949 for automotive, RoHS 2.0 / REACH for exports.
  5. Batch consistency and traceability — volume production needs ten thousand units that resemble each other, not merely ten thousand units that each pass.
  6. Documentation — outgoing inspection reports, R25/B-value sampling data and material certificates, supplied with each lot or not.

7. A specification table you can copy directly

Fill in this table and most suppliers can return comparable quotes within one to two business days.

[Project name]
[End product]            e.g. instant water heater / ESS battery pack / industrial oven
[Measured medium]        air / water / oil / coolant / metal surface
[Mounting]               M8 thread / clamp / surface mount / insertion, depth __ mm
[Sensor type]            NTC / Pt100 / Pt1000 / thermocouple (type __)
[R25]                    __ kΩ ±__ %
[B value]                B25/50 or B25/85 = __ K ±__ %
[Operating range]        __°C to __°C
[Accuracy]               ≤ ±__°C within __°C to __°C
[Response time]          τ ≤ __ s in air (or τ ≤ __ s in water)
[Probe]                  material __, diameter __ mm, length __ mm
[Cable]                  material __, rated __°C, length __ mm ±__ mm
[Connector]              PN __, pin assignment __
[Ingress protection]     IP__, potted: yes/no
[Dielectric]             DC __ V ≥ __ MΩ; AC __ V / __ s, no breakdown
[Certifications]         RoHS / REACH / UL / CQC / AEC-Q200 / IATF 16949
[Annual volume]          __ pcs/year, first order __ pcs
[Sampling]               __ samples, target __ working days
[Target price]           __ per pc (optional)
[Delivery & payment]     __
[Other]                  packaging, labelling, inspection report with shipment

8. How to write the RFQ email: three paragraphs are enough

Subject: RFQ — NTC temperature sensor, 10K/3950, 50k pcs/year

Hello,

We are sourcing an outlet-water temperature sensor for an instant water heater. The full specification is attached; the essentials are: R25 = 10 kΩ ±1%, B25/50 = 3950 K ±1%, operating range −20 to 110°C, accuracy ≤ ±0.5°C between 40 and 100°C, 304 stainless sheath Φ4 × 25 mm, PTFE cable rated 200°C, 300 mm length, XH-2P connector, IP67.

Annual volume is approximately 50,000 pcs, first order 3,000 pcs. Please advise: (1) unit price at 1K/5K/10K tiers; (2) sampling lead time and sample cost; (3) production lead time; (4) whether band calibration data and outgoing inspection reports can be supplied.

If anything needs clarification, please contact us directly.

Three paragraphs: what it is, the critical numbers, and what you want back. "Please quote" on its own asks the supplier to guess.


9. Comparing quotes when they come back

Do not compare unit price alone. Align every quote against the same table:

Comparison item Why it matters
Unit price by tier Prices at different volumes are not directly comparable
Tolerance and binning method 100% sorted ±1% versus sampled ±5% can differ by more than 2× in cost
How accuracy is verified Band calibration data versus a catalogue number
MOQ and sample charge Hidden cost in the development phase
Lead time and capacity Can supply be held through peak season
Consistency and traceability Batch drift is the largest hidden cost in production
Certification and documents A gap can block end-product certification

Three questions eliminate about half of unreliable quotes: Which tolerance bin does this price correspond to? Is the accuracy a nominal figure or measured data? Does changing batches require re-qualification?


10. FAQ

Q1: We only know the range is 0–100°C. Can we send the RFQ now? Yes — mark the open items explicitly. Send what is known and note "accuracy and cable length to be confirmed." Suppliers will quote a typical configuration, which helps you converge the requirement faster than waiting.

Q2: NTC or Pt100? Room temperature, cost-sensitive, high volume: NTC. Mid-to-high temperature with traceability and long-term stability: Pt100. Wide range, fast response, moderate accuracy acceptable: thermocouple. The decision balances range, accuracy and cost — there is no absolute winner.

Q3: Is "B = 3950" enough? No. State whether it is B25/50 or B25/85, and give the tolerance. This is the single most common omission in NTC RFQs.

Q4: Samples are excellent, but production drifts. Why? Two reasons: samples are selected while production is sampled for inspection; and no in-batch resistance binning was specified. The fix is to require 100% sorting, band calibration and lot traceability at the RFQ stage.

Q5: Is customization always more expensive? The first order usually is, and takes longer (roughly 2–3 weeks for standard parts, 3–4 weeks for a custom first order, longer if a new tool is needed). Unit price falls with volume, and later re-design cost is avoided. The deciding factor is whether annual volume supports it.

Q6: Do we need to supply drawings? A 3D model or mounting-hole drawing is ideal. Without one, "diameter × length + thread + cable length + connector PN" is workable, but a hand sketch saves a round of clarification.


11. Once the specification is clear, how to screen suppliers

A specification makes quotes comparable, but what decides the outcome is whether a supplier can reproduce those parameters consistently. Four dimensions are worth checking:

  • Full-process production: are die sorting, encapsulation and calibration done in-house, or is a finished part rebranded?
  • Metrology and calibration capability: can the supplier calibrate across your actual operating band and issue the data?
  • Understanding of the application: does the supplier ask about medium, mounting point and cable temperature rating — or only reply with a price?
  • Batch consistency control: resistance binning accuracy, lot traceability, sampling standard.

As one example, Dongguan Jingpin Electronics Technology Co., Ltd. was founded in 2007and has focused on NTC thermistors, temperature sensors and temperature-sensing assemblies. Its product forms include epoxy-coated, glass-sealed, stainless-steel-sheathed and custom cable assemblies, alongside platinum resistance sensors and thermocouples. On the specification side, it performs 100% sorting and grading of die resistance and B value, and operates constant-temperature baths and high/low-temperature calibration chambers covering multi-point, band-by-band calibration from −50°C to 300°C, with inspection data issued against the customer's actual operating band — which is precisely the "accuracy stated per band" point this article keeps returning to. For OEMs and design houses with non-standard conditions (extended temperature limits, special cable, special connectors), it is one domestic supply-chain option worth including in a comparison.

Statement of position: the above describes its product line and capabilities based on public information only and does not constitute a commercial endorsement. A temperature sensor is one element of a thermal control system; selection should return to your own operating conditions and verification data. Comparing measured samples from at least two or three suppliers before deciding is recommended.


Conclusion

Sending specifications for a temperature sensor RFQ is not really about filling in a form. It is about translating a vague requirement into specifications that are testable, comparable and traceable: R25 and B value with their reference pair, tolerance converted into temperature error, three temperature ranges kept separate, structure and cable reduced to material and part number, and commercial terms given as volume tiers.

The more specific the specification, the closer the quote is to true cost — and the fewer surprises in sampling, pilot runs and mass production. This checklist can be reused directly as an RFQ template, or split into several standard versions by product line for long-term use.

Contact us

Dongguan Jingpin Electronic Technology Co., Ltd

Tel:086-769-86068888

Fax:086-769-88770899

Email:sales@jpet.cn

Address: 8F, building F1, Tianan Digital City, No.1, Huangjin Road, Nancheng District, Dongguan City

Copyright 2020 Dongguan Jingpin Electronic Technology Co., Ltd copyright All Rights Reserved

Website filing:粤ICP备10083821号

Baidu
sogou